How to Get Rid of Wood Mites Naturally

How to Get Rid of Wood Mites Naturally

Do you ever wonder if you have wood mites that are hiding in your walls?

Do you wonder what they look like? Would you like to be able to identify them with a magnifying glass?

Would you like to sell your house and want to know how to get rid of wood mites for good? If you answered yes to any of these questions, then this article is for you.

In this article, you will learn how to get rid of wood mites using a few different methods.

How to Get Rid of Wood Mites Naturally

Wood mites that you observe in your home are most likely coming from outside. Keep your house as dry as possible to discourage wood mites from invading.

Mites leave a noticeable trail of their feces, which is a source of clues as to their location.

First, follow the route to the area where the wood mites are entering your home.

Look for a gap or crack in your caulking that may allow the wood mites to potentially enter your house. Caulking is pretty easy to replace, so it shouldn’t be too much of a hassle.

Don’t use a caulking gun here because the wood mites will scatter and you won’t be able to pinpoint them. Use a caulking knife or putty knife to apply an even coat of caulk to the crack.

Then go backwards to where the woodmite infestation started.

If you find the source, properly seal it up. That way, it can’t get back into your house.

Once the problem is taken care of, you can close up your building, tarp it, and walk away until the next time you have a problem.

You should try to discover an entry point where the wood mites were getting in.

It can be any crack or opening large enough to fit through, or an opening that is too small to be noticed. Use caulk to seal the opening so pests can’t sneak in.

Baseboards, plumbing, and beneath electrical outlets can prove particularly challenging. Moisture and airflow are two of those things that can harbor wood mites.

They like wood that is moist and humid, so if you notice your cabinets or furniture has water stains then there is an infestation. There are, however, safe and natural methods for eliminating these pests from your home.

A pesticide is the finest technique to supress wood mites.

It is to find them and eliminate them from the residence. Pesticides, on the other hand, are very toxic and should not be used inside.

There are, however, natural techniques to get rid wood mites from your house without the use of anything toxic.

Essential Oils

Cinnamon is an excellent essential oil to put in your diffuser. It is completely safe and has shown to be effective at removing some types of bugs.

Dusting and cleaning your house, particularly in high traffic areas, helps prevent the spread of mites.

Vacuum the carpet and furniture on a regular schedule.

Using one of the three natural ways listed is all that is required to dislodge mites and prevent their further infestation.

It would also assist if the source of the infestation can be eliminated.

Also, look for symptoms of wood mites on their pets, such as skin rashes and sores.

Keep contaminated wood outdoors until it can kill the mites.

Diatomaceous Earth

The sharp edges of these particles will pierce the exoskeletons of the mites, killing them.

They’ll give excellent protection to the plants and that way, there won’t be any wood mites in your yard.

Boric Acid

This is a safe and efficient way of getting rid of the insects. This can also be done using a spray.

Sprinkle some about your crops early in the morning.

Spray the wood mite hideouts with strong jets of water. Crack the treatment by leaving some of the infested plants on a warm windowsill for a few hours.

Also Read: How to Get Rid of Termites In Trees Naturally


So, these are the most tried and trusted methods for getting rid of wood mites naturally.

Make sure you know how the wood mites got into your home, and you must avoid attracting them in the future.

You might also heat contaminated wood using a coal iron.

Any wood mites or other pests on its surface will now be sealed inside it.

Allow it to cool before polishing it to ensure that you do not damage the object.

Author James